CC242ETOPCB

299,00 + TAX

In stock

CC242ETOPCB - GRAPHIC DISPLAY CONTROL UNIT FOR 1 OR 2 24V MOTORS + CHARGER + NiMH BATTERIES

CC242ETOPCB - ELECTRONIC CONTROL UNIT PROGRAMMERS FOR THE MANAGEMENT
OF ONE OR TWO ENCODER-CONTROLLED MOTORS + charger and NiMH batteries

Electronic CC242ETOPCB control unit programmer for encoder-controlled 24Vdc motors that allow
the precise position control of hinged and sliding gates fitted with a
multi-decoding module S449 - S486 - S504 - S508.
Batteries and battery charger in the CC242ETOPCB and
CC242EXTOPCB versions.

The electronic CC242ETOPCB control unit programmer is factory fitted with a graphic LCD display
(128 x 128 pixels) with backlighting in six different languages.
The menu allows you to read the number of manoeuvres carried out
and to rapidly set the system parameters including: the sequential button
mode, automatic reclosing, warning lamp pre-flashing, intermittent
warning lamp activation, indicator light, photoelectric cell function setting
and electric lock enable etc.

Compare
SKU: CA-CC242ETOPCB Categories: , ,

CC242ETOPCB – GRAPHIC DISPLAY CONTROL UNIT FOR 1 OR 2 24V MOTORS + CHARGER + NiMH BATTERIES

CC242ETOPCB – ELECTRONIC CONTROL UNIT PROGRAMMERS FOR THE MANAGEMENT
OF ONE OR TWO ENCODER-CONTROLLED MOTORS + charger and NiMH batteries

Electronic CC242ETOPCB control unit programmer for encoder-controlled 24Vdc motors that allow
the precise position control of hinged and sliding gates fitted with a
multi-decoding module S449 – S486 – S504 – S508.
Batteries and battery charger in the CC242ETOPCB and
CC242EXTOPCB versions.

The electronic CC242ETOPCB control unit programmer is factory fitted with a graphic LCD display
(128 x 128 pixels) with backlighting in six different languages.
The menu allows you to read the number of manoeuvres carried out
and to rapidly set the system parameters including: the sequential button
mode, automatic reclosing, warning lamp pre-flashing, intermittent
warning lamp activation, indicator light, photoelectric cell function setting
and electric lock enable etc.

ELECTRONIC PROGRAMMERS MICROPROCESSOR CONTROLLED FOR 24V MOTORS

MAINS POWER SUPPLY 230Vac
MOTOR OUTPUT 24Vdc
PROTECTION GRADE IP55
FIREPROOFING GRADE V2
AUTOMATIC GATE/DOOR PROGRAMMING
ELECTRONIC PROGRAMMERS
SELF-PROGRAMMING MONITORED
BY AN LCD GRAPHICS DISPLAY
CC242ETOP AND CC242EXTOPCB

The Electronic devices  CC242ETOPCB control unit for the control of automatic opening systems with one or two gate leaves: swing gates
and garage doors. Powered by 24Vdc they intelligently manage the movement of the gate.
Available in the following versions:
– with gate positioning control and encoder;
– with timer-controlled movement.

Both are equipped with a 433MHz FM radio receiver card.
Specially studied and designed for this type of use, these Cardin programmers are fitted with digital “step
by step” time programming which is easily carried out in real time while the gate is moving thus reducing
the installation time.

Monitoring the current consumption allows the control of a sophisticated anticrush safety system and the
“soft start” and “soft stop” functions reduce the stress on the mechanical components.
In CC242ETOPCB control unit  the simplified programming method uses one or two buttons (depending on the version) allowing all
functions to be programmed rapidly.

ALL WEATHER CONTAINER ABS IP55 WITH WALL FASTENING ELEMENTS

The electronic components of the CC242ETOP and PRG900 series are housed in a container with
sealing gaskets and cable gland entry holes for the insertion of Ø16mm rigid tubes.
The electronic components of the CC242EXTOPCB series are housed in a container with sealing gaskets
with:
– cover closing system using rapid action hooks;
– removable plaque factory set for the fastening of up to five cable clamps;
– air circulation slits built into the container;
– removable support in nylon fibre housing the electronic appliances on DIN rails;
– a Ø21 mm cable clamp and two Ø16mm cable clamps.

CC242ETOPCB ACCESSORIES

RSQ504OC2 – RSQ508OC2
RSQ504OC2 – RSQ508OC2 433 or 868MHz RECEIVERS to control the gates in remote control

SELINTBT8 : DIAGNOSTIC INTERFACE VIA CABLE/BLUETOOTH
Diagnostic interface fitted with 8 LEDs that represent respectively
the status of the 8 relay outputs. The status of the gate/boom and
of the safety devices and controls of the system can be obtained by
connecting the interface to a compatible Cardin CC242EXTOPCB control unit via MODBT
Bluetooth or MODCA cable.
The Bluetooth module is to be ordered separately.

KBNIMH-1  : KIT BATTERY CHARGER + NiMH BATTERIES
Allows the programmers PRG900 and CC242ETOP to work during
blackouts.

Additional information

Weight 4 kg
Dimensions 0,30 × 0,40 × 0,30 m
Be the first to review “CC242ETOPCB”

Your email address will not be published.

Reviews

There are no reviews yet.

See It Styled On Instagram

    No access token

Main Menu