PRG900

222,00 + TAX

In stock

PRG900 - GRAPHIC DISPLAY CONTROL UNIT FOR 1 OR 2 24V MOTORS

PRG900 - ELECTRONIC CONTROL UNIT PROGRAMMERS FOR THE MANAGEMENT OF ONE OR TWO MOTORS
Electronic PRG900 control unit programmer for the control of 24Vdc hinged gates with
intelligent time control functions that allow you to control the position of
the hinged and sliding gates, .

The PRG900 control uniti fitted with a multi-decoding module S449
- S486 - S504 - S508. Gate travel time programming is fully automatic
and guided by a 6-digit display which allows you to visualise the number
of manoeuvres carried out and to set several parameters such as the
type of motor, the torque setting and the limited opening distance.

Dip-switches allow you to set the system parameters including: the
sequential button mode, automatic reclosing, warning lamp pre-flashing,
intermittent warning lamp activation, indicator light and photoelectric cell
function setting and electric lock enable.

Compare
SKU: CA-PRG900 Categories: , , ,

PRG900 – GRAPHIC DISPLAY CONTROL UNIT FOR 1 OR 2 24V MOTORS

PRG900 – ELECTRONIC CONTROL UNIT PROGRAMMERS FOR THE MANAGEMENT OF ONE OR TWO MOTORS
Electronic PRG900 control unit programmer for the control of 24Vdc hinged gates with
intelligent time control functions that allow you to control the position of
the hinged and sliding gates, .

The PRG900 control uniti fitted with a multi-decoding module S449
– S486 – S504 – S508. Gate travel time programming is fully automatic
and guided by a 6-digit display which allows you to visualise the number
of manoeuvres carried out and to set several parameters such as the
type of motor, the torque setting and the limited opening distance.

Dip-switches allow you to set the system parameters including: the
sequential button mode, automatic reclosing, warning lamp pre-flashing,
intermittent warning lamp activation, indicator light and photoelectric cell
function setting and electric lock enable.

ELECTRONIC PROGRAMMERS MICROPROCESSOR CONTROLLED FOR 24V MOTORS

MAINS POWER SUPPLY 230Vac
MOTOR OUTPUT 24Vdc
PROTECTION GRADE IP55
FIREPROOFING GRADE V2
AUTOMATIC GATE/DOOR PROGRAMMING
ELECTRONIC PROGRAMMERS
SELF-PROGRAMMING MONITORED
BY AN LCD GRAPHICS DISPLAY
CC242ETOP AND CC242EXTOPCB

The Electronic devices  PRG900 control unit for the control of automatic opening systems with one or two gate leaves: swing gates
and garage doors. Powered by 24Vdc they intelligently manage the movement of the gate.
Available in the following versions:
– with gate positioning control and encoder;
– with timer-controlled movement.

Both are equipped with a 433MHz FM radio receiver card.
Specially studied and designed for this type of use, these Cardin programmers are fitted with digital “step
by step” time programming which is easily carried out in real time while the gate is moving thus reducing
the installation time.

Monitoring the current consumption allows the control of a sophisticated anticrush safety system and the
“soft start” and “soft stop” functions reduce the stress on the mechanical components.
In PRG900 control unit  the simplified programming method uses one or two buttons (depending on the version) allowing all
functions to be programmed rapidly.

ALL WEATHER CONTAINER ABS IP55 WITH WALL FASTENING ELEMENTS

The electronic components of the CC242ETOP and PRG900 series are housed in a container with
sealing gaskets and cable gland entry holes for the insertion of Ø16mm rigid tubes.
The electronic components of the CC242EXTOPCB series are housed in a container with sealing gaskets
with:
– cover closing system using rapid action hooks;
– removable plaque factory set for the fastening of up to five cable clamps;
– air circulation slits built into the container;
– removable support in nylon fibre housing the electronic appliances on DIN rails;
– a Ø21 mm cable clamp and two Ø16mm cable clamps.

PRG900 ACCESSORIES

RSQ504OC2 – RSQ508OC2
RSQ504OC2 – RSQ508OC2 433 or 868MHz RECEIVERS to control the gates in remote control

SELINTCV : VOLTAGE REGULATOR STABILIZED AT 24V (SERIES PRG900)
The device supplies a regulated 24Vdc voltage in output starting from
a direct current input that can vary from 19Vdc to 38Vdc. It is fitted
with 2 signal LEDs, one indicating the presence of voltage at the output
binding post and the other giving status information (correct operation,
overload, activated protection).

KBNIMH-1  : KIT BATTERY CHARGER + NiMH BATTERIES
Allows the programmers PRG900 and CC242ETOP to work during
blackouts.

Additional information

Weight 3 kg
Dimensions 0,30 × 0,40 × 0,30 m
Be the first to review “PRG900”

Your email address will not be published. Required fields are marked *

CAPTCHA ImageChange Image

Reviews

There are no reviews yet.

See It Styled On Instagram

    No access token

Main Menu