CK200

In stock

CK 200 / CK 200 - SENSITIVE EDGE CK200 / CK 200

CK 200 / CK 200 - SENSITIVE EDGE CK200 / CK 200
CK200 Resistive sensitive safty edge, according to the European standard EN 12978.

The CK200 has To be installed with CSSENSOR electronic card.
length 200 cm, without caps.

It is replaced by the new sensitive coasts:
MECHANICAL ACCESSORIES - SENSITIVE SAFTY EDGE ( RIBS) CARDIN with CODES:
NC8K2Lxxx
BBASLxxN
CPxxBL
BSHxxLxx

Compare

CK 200 / CK200 – SENSITIVE EDGE CK200 / CK 200

CK 200 / CK200 – SENSITIVE EDGE CK200 / CK 200
CK200 Resistive sensitive safty edge, according to the European standard EN 12978.

The CK 200 has To be installed with CSSENSOR electronic card.
length 200 cm, without caps.

It is replaced by the new sensitive coasts:
MECHANICAL ACCESSORIES – SENSITIVE SAFTY EDGE ( RIBS) CARDIN with CODES:
NC8K2Lxxx
BBASLxxN
CPxxBL
BSHxxLxx

AUXILIARY AND SAFETY DEVICES FOR SWING GATES, SLIDING GATES AND GARAGE DOORS

The safety edge is made up of a rubber profile with elastic impact absorption and an aluminium
profile. which is fixed to the column or the gate and acts as a support for the safety edge.
Its operating principle is based on detection (active along the entire length of the safety edge).
The detection via the crushing pressure applied by an obstacle or a mass that is located within the operating sphere of the closing
device that is fitted with the protection.

The deformation of the rubber profile causes the safety edge
to create a contact, which is then sent (by cable or by radio) to a control centre,
which in turn activates a STOP command.

Active mechanical safety edge with an N.C. contact for sliding gates / swing gates CK 200 .
The mechanical safety edge is used as a safety device in installations with automatic sliding gates with
horizontal movement and on other closing device installations (hinged gates etc.).
Where there is a real risk of crushing or trapping.
Operation of the device is guaranteed by 2 micro-switches.
Both of them intervene when the safety edge and/or the pliable end caps are deformed.

Safety edge for garage doors N.C. contact CK 200 .

This mechanical device is an extremely versatile safety edge in aluminium that can be fitted to
overhead garage doors, rolling shutters and other industrial closing devices.
The edges are fitted with sealed micro-switches and have a series of accessories
permitting a variety of combinations and uses.

Low profile / high profile passive edge CK 200 .
Although it is not to be considered a safety device due to the absence of an electrical contact,
the passive edge has the same dimensions and mechanical protective characteristics as
active safety edge and does supply valid absorption protection against impact.
The low profile edge, which works as simple impact protection, is suitable for closing
devices where passing room is limited.

Conductive safety edge 8,2kΩ contact
The safety edges are used to eliminate the risk of crushing or shearing
caused by sliding doors, bulkheads, automatic gates etc.
They respect the requirements of the impact curve as stipulated in EN12453.
The edges are made up of a C-shaped aluminium support and a PVC profile in which a
safety sensor has been inserted.

When the profile is deformed or crushed the two metal contacts of the sensor
come into contact causing the alarm situation.
The ample height of the rubber profile and the insert in conductive
rubber allow rapid intervention times fully respecting the standards and
regulations in force.

Additional information

Weight 5 kg
Dimensions 2,50 × 0,2 × 0,2 m
Be the first to review “CK200”

Your email address will not be published. Required fields are marked *

CAPTCHA ImageChange Image

Reviews

There are no reviews yet.

See It Styled On Instagram

    No access token

Main Menu